|
Stampable
Concrete Overlay
Technical Bulletin
Purchase
Stampable Concrete Overlay at Monster Constructors Store
DESCRIPTION: A pre-blended product
that can be used on existing concrete surfaces.
This material
is placed approximately 3/8” thick and imprinted with a mat
type tool to create
impressions such as stone, brick, tile, or
other authentic type surfaces. This product can
be used on
exterior floors, driveways, patios, pool decks, and other surfaces for
vehicular
and pedestrian traffic.
Surface Preparation: All surfaces shall be
clean and free of dirt, dust, paint, sealers,
form releases,
curing agents, grease, oil, or any inhibiting mixed material that would
impede
the penetration of Unipas Polymer to the substrate pores. Any material
that would
cause de-lamination must be removed. Pressure
washing, sand blasting, water blasting,
grinding &
shot blasting are suggested procedures for removing contaminants from
the
surface. On existing surfaces not subject to these
conditions, pressure washing and 30
parts water to 1 part acid
should be considered for smooth, steel troweled, or formed
concrete.
Mixing & Application:
1.
Bonding Primer: Begin with a properly prepared Saturated Surface Dry
substrate.
Apply Concrete Colors Unipas Polymer undiluted over
saturated substrate. Scrub
polymer into the surface with a
medium to stiff broom or brush. Make sure to
cover all areas
that will be receiving the stampable overlay mixture. Allow this
primer
to dry to a clear film. Do not walk on the dried primer unless the use
of
proper footwear that will not tear the film from the
concrete has been attained.
Suggested footwear, rubber spikes.
2.
Depending on the desired application, the addition of water and Unipas
polymer
is as follows, add 2.5-3 quarts of clean potable water
and 2.5-3 quarts of Unipas
polymer to a 50lb bag of Concrete
Colors overlayment. Slowly add the 50lb.
mixture of
overlayment to the water / Unipas combination and mix for approx. 3
to
4 minutes, until a lump free consistency has been obtained. Place
material onto
the surface and screed with a gauge rake set to
the desired thickness. Smooth out
material with a fresno, or
hand held pool trowels to consolidate the material.
Allow the
material to gain sufficient structural integrity to accept imprinting
tools for impression work or for smooth trowel if desired.
For
imprinted work, a powder release agent or liquid release agent can be
used.
After imprinting or other surface textures have been
completed, allow 4-7 days for curing
Precautions:
•
Do not allow the Unipas Polymer mixture to freeze.
•
Apply between the temperatures of 60 – 100 degrees Fahrenheit.
•
Allow 4-7 days of curing before opening to vehicular traffic.
•
Keep installed material from freezing for a minimum of 48 hours.
Warning: This product contains
Portland cement; avoid eye contact or prolonged contact
with
skin. Wash thoroughly after handling. In case of eye contact, flush
with water for 15
minutes. Consult a physician immediately.
Keep out of the reach of children. Contains
free silica
– Do Not breath dust. May cause delayed lung injury. Follow
OSHA safety
and health standards for crystalline silica
(quartz). See Material Safety Data Sheets for
detailed
information.
Coverage Rates: A 50lb unit of one
component stampable overlay will cover
approximately 16 square
feet @ 3/8” thick, or 25 square feet at ¼ thick.
DO NOT TAKE THIS
PRODUCT INTERNALLY
Keep Out Of Reach Of
Children
Purchase
Stampable Concrete Overlay at Monster Constructors Store
THINK GREEN. We use
recycled concrete in lieu of gravel as aggregate in our
concrete. It doesn't cost us any extra; thus, it doesn't cost
you any extra. As far as structure, the recycled concrete is
just as strong as the gravel. We do what we can to save the
limited resources we have on earth.
Keep
in
mind we do work all over
the DFW metroplex, including Dallas, Fort Worth, Arlington, Plano,
Irving, Carrollton, Richardson, Denton, Garland, Grand Prairie,
Addison, Allen, Azle, Bedford, Benbrook, Burleson, Cleburne,
Colleyville, Cedar Hill, Coppell, Corinth, DeSoto, Duncanville, Ennis,
Euless, Farmers Branch, Flower Mound, Frisco, Haltom City, Highland
Village, Hurst, Keller, Lewisville, Mansfield, Midlothian, North
Richland Hills, Southlake, The Colony, University Park, Watauga,
Weatherford, White Settlement, and surrounding towns and
cities.
Curious if you are within our scope? Contact us:
Click Here.
|
